$58.04
On Hold
SUPROTEC Additive Active Plus in engine oil 90ml Diesel, Gasoline, Gas
More than 10 available
Details
Shipping: Australia: free (more destinations)
Condition: Brand new
Returns: 7 days, buyer pays return shipping (more)
Additive Active Plus in engine oil
Tribological composition (or "additive") to restore the performance characteristics of engines of any type and design (including turbocharging) with a working volume of up to 2.5 liters. Provides restoration of compression, power, throttle response, effective fuel consumption, as well as to extend the life and protection against breakdowns in emergency situations.
The tribotechnical composition does not react with motor oils and their packages of chemical additives, does not change their properties and characteristics.
"Active Plus" is a universal composition that came to replace a number of products of the previous generation. The compositions that he replaces are shown in the diagram on the right.
EFFECTS FROM APPLICATION
The composition of "Active Plus" has an optimal composition of active components, which is equally effective for engines of any type and design with a working volume of 1.5 to 2.5 liters and with an oil system of 4 to 7 liters. For engines with lower parameters it is recommended to use the composition "Active Standard".
APPLICATION PROCEDURE
For use, the composition must be thoroughly shaken so that the active component in the form of a gray-green precipitate completely disperses throughout the volume of the vial and pour the mixture into the oil filler neck. This does not require any special knowledge or tools.
A full engine treatment cycle will require two or three bottles, depending on the condition of the engine. The composition is added in accordance with the schedule for changing the oil in the engine.
Adding the composition to the engine oil can be done by any car owner on any car independently. However, it is important to pay attention to the paragraphs of the instructions attached to each bottle of the composition so that it works as efficiently as possible.
The standard processing procedure is as follows:
A bottle of the composition is added to the oil about 1000 kilometers before the planned regular oil change.
Another bottle of the composition is added after replacement already in fresh oil and works there throughout the interservice run.
For vehicles with a mileage of more than 50,000 kilometers, in order to achieve maximum recovery effect, it is strongly recommended to add the composition for the third time after the next oil change.
Tribological composition (or "additive") to restore the performance characteristics of engines of any type and design (including turbocharging) with a working volume of up to 2.5 liters. Provides restoration of compression, power, throttle response, effective fuel consumption, as well as to extend the life and protection against breakdowns in emergency situations.
The tribotechnical composition does not react with motor oils and their packages of chemical additives, does not change their properties and characteristics.
"Active Plus" is a universal composition that came to replace a number of products of the previous generation. The compositions that he replaces are shown in the diagram on the right.
EFFECTS FROM APPLICATION
The composition of "Active Plus" has an optimal composition of active components, which is equally effective for engines of any type and design with a working volume of 1.5 to 2.5 liters and with an oil system of 4 to 7 liters. For engines with lower parameters it is recommended to use the composition "Active Standard".
APPLICATION PROCEDURE
For use, the composition must be thoroughly shaken so that the active component in the form of a gray-green precipitate completely disperses throughout the volume of the vial and pour the mixture into the oil filler neck. This does not require any special knowledge or tools.
A full engine treatment cycle will require two or three bottles, depending on the condition of the engine. The composition is added in accordance with the schedule for changing the oil in the engine.
Adding the composition to the engine oil can be done by any car owner on any car independently. However, it is important to pay attention to the paragraphs of the instructions attached to each bottle of the composition so that it works as efficiently as possible.
The standard processing procedure is as follows:
A bottle of the composition is added to the oil about 1000 kilometers before the planned regular oil change.
Another bottle of the composition is added after replacement already in fresh oil and works there throughout the interservice run.
For vehicles with a mileage of more than 50,000 kilometers, in order to achieve maximum recovery effect, it is strongly recommended to add the composition for the third time after the next oil change.
RU, RUSSIAN FEDERATION